Back to Blog
How-to Guides 2026-11-13 Yoshimura R&D of America, Inc. 0 views

Exhaust Spring and Spacer Replacement Guide

Exhaust Spring and Spacer Replacement Guide

Learn how to replace exhaust springs, spacers, and button head cap screws on your Yoshimura system. This guide covers common hardware parts and when to call for help.

What This Guide Covers

Exhaust systems take a beating from heat, vibration, and road debris. Over time, small hardware like springs, spacers, and cap screws can wear out or get lost. Replacing them keeps your Yoshimura system secure and looking clean. This guide explains the common replacement parts and what to check before you order.

The parts covered here are straightforward to replace, but the supplied catalog does not include step-by-step instructions for every model. When you don't see a specific procedure, use the general approach described below and contact Yoshimura if you have questions.

Common Replacement Hardware

  • 6mm X 20mm BUTTON HEAD CAP SCREW: 6mm X 20mm BUTTON HEAD CAP SCREW – a small, low-profile fastener used to secure exhaust components. Sold as a standard replacement part. Button head cap screws are often the first thing to loosen or strip. Having a spare on hand saves a trip to the hardware store.
    6mm X 20mm BUTTON HEAD CAP SCREW
    6mm X 20mm BUTTON HEAD CAP SCREW
  • 22/25 x 8.5 x 30 Aluminum Spacer: 22/25 x 8.5 x 30 Aluminum Spacer – a precision-machined spacer that fits between mounting brackets and the exhaust. Made from aluminum for corrosion resistance. Spacers maintain correct alignment and prevent metal-on-metal contact. A worn or missing spacer can cause rattling or misalignment.
    22/25 x 8.5 x 30 Aluminum Spacer
    22/25 x 8.5 x 30 Aluminum Spacer
  • RMZ/KX250F 04-05 Stainless Heatshield: RMZ/KX250F 04-05 Stainless Heatshield – a replacement shield that bolts directly to your Yoshimura system. Made from stainless steel to resist heat and impact. Heatshields protect your leg and nearby components from exhaust heat. Replacing a cracked or faded shield restores the system's look and safety.

When to Replace Exhaust Springs and Spacers

Exhaust springs lose tension over time, especially on systems that see frequent thermal cycling. If you notice the muffler moving more than usual or hear a metallic rattle at idle, the springs may need replacement. Spacers rarely wear out unless they get crushed or corroded, but they can fall off if the retaining hardware loosens.

Button head cap screws are prone to stripping if overtightened or if the threads are dirty. Always inspect the screw head and threads before reuse. If the hex drive feels rounded, replace the screw.

General Replacement Steps

  1. 1. Gather the correct parts: Identify the exact fastener or spacer you need. The catalog lists button head cap screws (6mm x 20mm), aluminum spacers (22/25 x 8.5 x 30), and stainless heatshields for specific models. If you're unsure, contact Yoshimura at 800-634-9166 or [email protected].
  2. 2. Remove the old hardware: Use the appropriate hex key or socket to remove the cap screw. If the spacer is stuck, gently tap it with a soft mallet. For heatshields, remove the screws holding the shield to the exhaust body.
  3. 3. Clean the mounting area: Wipe away any dirt, grease, or old thread locker. A clean surface ensures the new hardware seats properly.
  4. 4. Install the new part: Hand-thread the cap screw into the threaded hole. For spacers, slide them into position before tightening. For heatshields, align the shield and secure it with the provided screws. Tighten to a firm hand-tight plus a quarter turn; avoid overtightening.
  5. 5. Check for secure fit: Gently wiggle the exhaust or heatshield to confirm there's no movement. If the part feels loose, double-check alignment and torque.

What the Catalog Doesn't Tell You

The catalog does not specify torque values, thread locker recommendations, or exact installation sequences for these parts. If your system uses a different fastener size or spacer dimension, you'll need to verify compatibility. The catalog notes that if you're "not finding what you need," you should call or email Yoshimura for assistance.

For heatshields, the catalog says they "bolt right up" but does not guarantee fitment for non-stated models. Always confirm your exhaust model and year before ordering.

When to Call Yoshimura

If you can't find the exact part on the site, or if your exhaust uses a non-standard fastener, contact Yoshimura directly. Their team can help identify the correct replacement. The catalog provides phone (800-634-9166) and email ([email protected]) support for these situations.

Related Articles

Customer Service
Home
Products
Cart
Profile