XSR700 Fender Eliminator Kit: Install and Fitment FAQ

What the XSR700 Fender Eliminator Kit includes

The Yoshimura Fender Eliminator Kit for the 2018-2021 Yamaha XSR700 is a model-specific kit designed to clean up the rear end of your motorcycle. It includes a precision laser-cut stainless steel bracket that tucks discreetly under the tail section, a black anodized aluminum license plate frame with a silk-screened Yoshimura logo, and a new DOT-compliant LED light with a weather-tight housing.

The kit also comes with heat shrink solder sleeve butt connectors for wiring, making the electrical connections easier and more durable. It is proudly made in the USA and designed for USA-spec license plates measuring 4" x 7" with a 5-3/4" horizontal hole spacing and 2-3/4" vertical hole spacing.

Kit specifications at a glance

• XSR700 18-21 Fender Eliminator Kit: Model specific precision laser-cut stainless steel bracket tucks discreetly under the tail section of the motorcycle This bracket is designed specifically for the XSR700, ensuring a clean fit without universal adapters.

  

• XSR700 18-21 Fender Eliminator Kit: Designed for USA Spec License plates measuring 4" x 7" Check your plate size before ordering; this kit will not fit plates with different dimensions.
• XSR700 18-21 Fender Eliminator Kit: 5-3/4" horizontal hole spacing and 2-3/4" vertical hole spacing These measurements must match your license plate's mounting holes for direct bolt-on installation.
• XSR700 18-21 Fender Eliminator Kit: Compatible with aftermarket turn signals when combined with Universal Turn Signal Standard Bracket Kit or Corner Mount Bracket Kit (sold separately) If you plan to swap turn signals, you'll need one of these additional kits.

Step-by-step installation overview

The exact procedure may vary slightly depending on your motorcycle's configuration, but the general process for installing the Yoshimura Fender Eliminator Kit is as follows. Always consult your owner's manual and use proper tools.

1. Prepare your workspace: Gather basic hand tools, including wrenches and screwdrivers, and ensure you have a clean, well-lit area. Disconnect the battery before working on electrical components.
2. Remove the stock fender assembly: Unbolt and disconnect the original fender, taking care to unplug the stock license plate light and turn signals. Keep any hardware that may be reused.
3. Test-fit the new bracket: Position the laser-cut stainless steel bracket under the tail section to confirm alignment with the mounting points. Do not fully tighten bolts yet.
4. Attach the license plate frame and light: Mount the black anodized aluminum license plate frame to the bracket using the provided hardware. Install the DOT-compliant LED light and housing, ensuring the weather-tight seal is properly seated.
5. Wire the LED light and turn signals: Use the supplied heat shrink solder sleeve butt connectors to splice the LED light wires into the stock harness. If you are installing aftermarket turn signals, refer to the separate bracket kit instructions.
6. Secure all connections and check operation: Apply heat to shrink the solder sleeves, then test the LED light and turn signals for proper function. Tighten all bolts to the manufacturer's specifications.

Fitment checks before you start

Before you begin, verify these key fitment points to avoid surprises.

• License plate size: The kit is designed for USA-spec plates measuring 4" x 7". Measure your plate to confirm.
• Hole spacing: Ensure your license plate has 5-3/4" horizontal and 2-3/4" vertical hole spacing. If not, you may need to drill new holes or use an adapter.
• Turn signal compatibility: The kit works with aftermarket turn signals only when combined with the Universal Turn Signal Standard Bracket Kit or Corner Mount Bracket Kit (sold separately). Stock turn signals may not be directly compatible.
• Model and year: This kit is specifically for the 2018-2021 Yamaha XSR700. Verify your model year before ordering.

Wiring tips for a clean install

The included heat shrink solder sleeve butt connectors simplify the wiring process. These connectors require a heat source, such as a heat gun, to melt the solder and shrink the tubing for a secure, weather-resistant connection. Always disconnect the battery before wiring, and follow the instructions provided with the connectors. If you are not comfortable with electrical work, consider having a professional install the kit.

The new LED light housing is designed to be weather-tight, but ensure that all connections are properly sealed and that wires are routed away from moving parts or excessive heat.

Product facts: XSR700 Fender Eliminator Kit

• XSR700 18-21 Fender Eliminator Kit: New improved D.O.T. compliant L.E.D. light and housing The included light meets DOT requirements and is designed for durability.
• XSR700 18-21 Fender Eliminator Kit: New easy to use Heat Shrink Solder Sleeve Butt Connectors These connectors make wiring straightforward and reliable.
• XSR700 18-21 Fender Eliminator Kit: Black anodized aluminum license plate frame with silk screened Yoshimura logo included Adds a finished look and includes branding.
• XSR700 18-21 Fender Eliminator Kit: Proudly made in the USA! Indicates domestic manufacturing.