Volver al blog
Guías prácticas 2026-11-21 Yoshimura R&D of America, Inc. 0 vistas

RS-12 ADV Slip-On for V-Strom 800: Fitment & Install

RS-12 ADV Slip-On for V-Strom 800: Fitment & Install

Learn how the Yoshimura RS-12 ADV slip-on exhaust fits the Suzuki V-Strom 800 and what to expect during installation, including performance gains and weight savings.

What the RS-12 ADV Slip-On Changes on Your V-Strom 800

The Yoshimura RS-12 ADV slip-on exhaust is designed specifically for the Suzuki V-Strom 800 (2023–2026 models). It uses a 776cc parallel-twin engine with a 270-degree crankshaft, and the RS-12 ADV muffler is tuned to complement that firing order. The slip-on replaces the stock muffler and tailpipe section, retaining the factory header pipes.

Yoshimura developed this system for adventure riding, so it balances a deeper tone with off-road practicality. The RS-12 ADV is built with a stainless steel muffler and a Works Finish, giving it a durable, matte appearance that hides trail scuffs better than polished chrome.

RS-12 ADV Key Facts

Installation Steps for the RS-12 ADV Slip-On

The following steps are based on typical slip-on exhaust installation. Always refer to the product instructions for torque values and specific procedures.

  1. Prepare the bike: Park the V-Strom 800 on a level surface and let the exhaust cool completely. Remove any side cases or luggage that obstruct access to the muffler.
  2. Remove the stock muffler: Loosen the clamp connecting the muffler to the mid-pipe and the hanger bolt securing the muffler to the frame. Slide the stock muffler off the mid-pipe and remove the hanger bracket if needed.
  3. Install the RS-12 ADV muffler: Slide the RS-12 ADV slip-on onto the stock mid-pipe. Align the hanger bracket with the frame mount. Hand-tighten the clamp and hanger bolt to hold the muffler in position.
  4. Adjust alignment: Check that the muffler is centered and does not contact the swingarm, rear shock, or bodywork. Tighten the hanger bolt to the manufacturer's recommended torque.
  5. Secure the clamp: Tighten the mid-pipe clamp to the specified torque. Ensure the joint is sealed and there are no exhaust leaks.
  6. Final check: Start the engine and listen for any unusual noises or leaks. Let the bike idle for a few minutes, then check that the muffler remains properly aligned.

Fitment and Compatibility Notes

The RS-12 ADV slip-on fits all 2023–2026 Suzuki V-Strom 800 models, including the V-Strom 800DE. It is a direct replacement for the stock muffler and does not require remapping or ECU tuning, though a fuel controller may optimize the small performance gains.

Yoshimura includes a carbon fiber heat shield that is custom-molded for the V-Strom 800 tailpipe. This shield protects the rider's leg and luggage from exhaust heat while adding a distinctive look.

Note: A spark arrestor is sold separately if you ride in areas that require one. The system is compatible with Yoshimura's SA-19-K spark arrestor.

What the Catalog Does Not Settle

The supplied information does not include specific sound level measurements or detailed installation torque values. For exact sound output and torque specs, refer to the product instructions or contact Yoshimura directly.

The RS-12 ADV is not a full exhaust system; it replaces only the muffler. If you are looking for maximum power gains, a full system with a header pipe may be a better choice, but it will require rejetting or a power commander.

Artículos relacionados

Customer Service
Inicio
Productos
Carrito
Perfil