Install a Fender Eliminator on Suzuki GSX-8T

By Yoshimura R&D of America, Inc. | Published: 2026-10-22

Category: How-to Guides

Step-by-step guide to installing a V2 Fender Eliminator Kit on your Suzuki GSX-8T or TT. No wire stripping needed, with plug-and-play connections for a clean rear end.

Quick answer

Installing a V2 Fender Eliminator Kit on a Suzuki GSX-8T is a straightforward job that takes about an hour. The kit uses plug-and-play wiring, so you don't have to strip or splice any wires.

Why upgrade the rear end on a GSX-8T?

The stock fender on the Suzuki GSX-8T is bulky and extends far behind the tail, which can make the bike look unfinished. A fender eliminator kit cleans up the rear profile, tucks the license plate closer to the tail, and often improves the visibility of the turn signals. The V2 design from Yoshimura is built specifically for the GSX-8T and TT models, so fitment is precise and the included wiring harness connects directly without modification.

What to know before you start

This install does not require cutting or stripping any factory wires. The V2 kit includes a plug-and-play harness that mates with the stock connectors. You will still need basic hand tools: a socket set, hex keys, and a trim removal tool or flathead screwdriver. Work on a level surface and have the bike on a rear stand or center stand for stability.

Installation steps

Remove the stock fender: Start by disconnecting the battery to avoid any accidental shorts. Remove the rear seat and tail section to access the fender mounting bolts. Unbolt the stock fender from the subframe, then disconnect the turn signal and license plate light connectors. Carefully pull the fender off the bike. Common mistake: Forgetting to disconnect the battery can cause a short if a live wire touches the frame. Always disconnect it first.
Prepare the V2 kit base: Lay the new V2 base on a clean surface. Attach the included LED tail light to the base using the provided screws. Do not tighten fully until you've aligned everything. Route the plug-and-play wiring harness through the base so it exits cleanly toward the front of the bike. Common mistake: Overtightening the tail light screws before alignment can crack the plastic base. Snug them only until the light is secure, then adjust after final fitment.
Mount the base to the subframe: Position the V2 base against the subframe mounting points. Use the original bolts from the stock fender or the new hardware included in the kit. Tighten in a cross pattern to ensure even pressure. The base should sit flush against the subframe without gaps. Common mistake: Using the wrong length bolts can strip the subframe threads. Test each bolt by hand before using a tool.
Connect the wiring: Plug the kit's harness into the stock connectors: tail light, turn signals, and license plate light. Each connector is shaped differently, so you can't mix them up. Verify that all connections click fully into place. Use zip ties to secure any excess wire to the subframe, keeping it away from moving parts. Common mistake: Leaving loose wiring can cause chafing against the tire or swingarm. Secure all slack with zip ties.
Install the license plate mount and final check: Attach the license plate bracket to the base using the supplied hardware. Mount your plate and tighten the bolts. Reconnect the battery, then test all lights: tail, brake, turn signals, and plate light. Reinstall the tail section and rear seat. Common mistake: Forgetting to test the lights before reassembling the tail can lead to having to take everything apart again. Always test first.

Product details

GSX-8T / TT 2026 V2 Fender Eliminator Kit: The V2 Fender Eliminator Kit for the Suzuki GSX-8T / TT features a redesigned base with model-specific plug-and-play wiring for the custom LED tail light. This means you can install the kit without stripping or splicing any wires, reducing the risk of electrical issues and saving time.
GSX-8T / TT 2026 V2 Fender Eliminator Kit