Back to Blog
Product Reviews 2026-11-17 Yoshimura R&D of America, Inc. 0 views

Type F Standard LED Signal Kit: V2 Fender Eliminator Fit Guide

Type F Standard LED Signal Kit: V2 Fender Eliminator Fit Guide

What the Type F Standard LED Signal Kit includes, how it mounts to a Yoshimura V2 Fender Eliminator, and which fitment and wiring points to confirm before you install.

What the Type F Standard kit is built to do

The Type F Standard LED Signal Kit is a complete turn-signal package for the Yoshimura V2 Fender Eliminator Kit. It pairs a sequential two-wire LED signal with a powder-coated stainless steel mounting bracket designed for the V2, plus the wiring pieces needed for a plug-and-play connection where your bike model requires them.

That combination is the reason to start here rather than with a universal signal: the bracket and adapters are matched to the V2 fender eliminator, so the install is about confirming your bike's wiring and following the V2 instructions rather than fabricating a mount.

What comes in the box

  • Type F Standard LED Signal Kit for V2 Fender Eliminators: Complete LED Kit contains a CE certified set of sequential two-wire LED lights with a clear lens, anodized black aluminum body in a rubber insulated mount to decrease vibration, an LED relay module, and mounting hardware. The relay module and hardware are included, so you can plan the install around the supplied components instead of sourcing them separately.
    Type F Standard LED Signal Kit for V2 Fender Eliminators
    Type F Standard LED Signal Kit for V2 Fender Eliminators
  • Type F Standard LED Signal Kit for V2 Fender Eliminators: The kit includes OEM plug wiring adaptors and a powder-coated stainless steel mounting bracket designed for the Yoshimura V2 Fender Eliminator Kit. These are the two parts that make this a V2-specific signal kit rather than a generic LED light.
  • Type F Standard LED Signal Kit for V2 Fender Eliminators: One specially designed Yoshimura turn signal bracket mounts on all USA license plates. If you run a USA plate, the bracket is intended to work with it; confirm your plate setup before install.

A sensible order for the install

  1. Read the V2 fender eliminator instructions first: The product listing directs you to your specific V2 Fender Eliminator Kit instructions for the signal bracket and light instructions. Start there so the signal work follows the same sequence as the fender kit.
  2. Test-fit the bracket and lights before final tightening: The bracket is designed for the V2 and mounts on USA license plates. Check the signal position and clearance with the fender eliminator in place before you commit to final hardware torque.
  3. Route the two-wire signal leads and connect the adapters: The kit uses sequential two-wire LED lights with OEM plug wiring adaptors. Connect the plug-and-play adapters where your bike model requires them, and keep the LED relay module in the circuit as supplied.
  4. Check signal operation before you finish: With the lights and relay module connected, confirm the signals operate as expected before you button up the tail. If anything is unclear, stop and consult the V2 instructions rather than improvising.

Fitment and wiring points to confirm before you order

  • Your fender eliminator is the V2: The bracket and kit are described specifically for the Yoshimura V2 Fender Eliminator Kit. Confirm your fender eliminator version before buying.
  • Your bike's connector setup: Plug-and-play adapters are included if your bike model requires them. The supplied information does not list every model, so check your bike's turn-signal connectors against the kit contents.
  • Your license plate type: The bracket is described as mounting on all USA license plates. If you run a non-USA plate, verify the bracket will work with your plate before ordering.
  • The LED relay module: The kit includes an LED relay module. Plan for where it will live in the tail so the wiring stays tidy.

What the supplied information does not settle

The listing does not confirm model-by-model fitment, signal dimensions, or a torque specification for the bracket hardware. It also does not state whether the kit replaces or supplements every stock turn-signal function on every bike. Those are questions to resolve with your V2 fender eliminator instructions or your bike's service information before you start.

The kit is offered in a Standard variant. If your decision depends on a different lens color, signal length, or connector type, confirm it against the supplied kit contents rather than assuming.

Who this kit suits

Choose the Type F Standard LED Signal Kit if you already run a Yoshimura V2 Fender Eliminator and want a matched signal setup with a V2-specific bracket, plug-and-play adapters, and an included relay module. If you are still choosing a fender eliminator, settle that first — this kit is built around the V2, not a universal tail.

Related Articles

Customer Service
Home
Products
Cart
Profile